rear seatbelt install
Moderators: GAHorn, Karl Towle, Bruce Fenstermacher
rear seatbelt install
I am putting an Innovation Airframe single rear seat in my c170. Directly behind the seat and about 14 inches back is a nut plate. I believe it is for a 3/16 bolt. Is this strong enough for attaching the belt (both sides)? I have not been able to get clear information on this.
-
- Posts: 3485
- Joined: Sat May 06, 2006 6:05 pm
Re: rear seatbelt install
The original rear seat was attached to the airframe by four bolts, one on each side of the seat, one directly under the seat, and the bolt that engages that nut plate you describe behind and centered in the airframe side-to-side. The four seat belt attach points were on the seat frame assembly itself but did not connect directly to any seat attach bolt. A structural analysis would have to be done to get a definitive answer and that has not been done as far as I know on the 170. You will have to decide if it can safely be done.
But, to help in your decision, the C185 with separate rear seats, have their center rear seat belts bolted directly to that same center attach point you describe.
But, to help in your decision, the C185 with separate rear seats, have their center rear seat belts bolted directly to that same center attach point you describe.
Richard Pulley
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
Re: rear seatbelt install
Richard, does the B model 170 have cargo tie down nutplates back behind the backseat on either side?
I know on my '56 172 there are either 2 or 4 nutplates (I think 4) with two of them being forward and the other two being farther back. I just don't remember how far back. Just wondering if those, if they exist in the B model and are far enough back, might be as strong as the back anchor on our factory rear seats? I once made a couple of homemade, screw in tie down anchors from some steel stock and threaded the end so it would screw into the aft anchors. Since I don't weld, I used brute force and a vise to bend both anchors into loops. Only used them once to hold some tool boxes, etc. and they seemed adequate.
I know on my '56 172 there are either 2 or 4 nutplates (I think 4) with two of them being forward and the other two being farther back. I just don't remember how far back. Just wondering if those, if they exist in the B model and are far enough back, might be as strong as the back anchor on our factory rear seats? I once made a couple of homemade, screw in tie down anchors from some steel stock and threaded the end so it would screw into the aft anchors. Since I don't weld, I used brute force and a vise to bend both anchors into loops. Only used them once to hold some tool boxes, etc. and they seemed adequate.
OLE POKEY
170C
Director:
2012-2018
170C
Director:
2012-2018
Re: rear seatbelt install
The nut plate I am thinking of using is not for the seat but 1/4 of the way in from the side and parallel with the seat nut plate.
Re: rear seatbelt install
Since those seats are PMA copies of Cessna 180/185 middle row seats it would seem that using the same method and attach points for the seat belts that Cessna uses in the 180/185 would be the easy solution rather than trying to reinvent the wheel. Take a look at the mid 60's and newer parts manual.
Tim
Tim
-
- Posts: 3485
- Joined: Sat May 06, 2006 6:05 pm
Re: rear seatbelt install
Frank, I'm not familiar with the nut plates you are referring to, sorry.170C wrote:Richard, does the B model 170 have cargo tie down nutplates back behind the backseat on either side?..............
Richard Pulley
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
Re: rear seatbelt install
It's really difficult to know what you're describing (or even to determine if what you're describing is common to all models... maybe you have a unique situation?) ...without a picture. Does the Innovation Airframe people have an answer for you?dogone wrote:I am putting an Innovation Airframe single rear seat in my c170. Directly behind the seat and about 14 inches back is a nut plate. I believe it is for a 3/16 bolt. Is this strong enough for attaching the belt (both sides)? I have not been able to get clear information on this.
'53 B-model N146YS SN:25713
50th Anniversary of Flight Model. Winner-Best Original 170B, 100th Anniversary of Flight Convention.
An originality nut (mostly) for the right reasons.
50th Anniversary of Flight Model. Winner-Best Original 170B, 100th Anniversary of Flight Convention.
An originality nut (mostly) for the right reasons.
- ghostflyer
- Posts: 1403
- Joined: Mon Apr 21, 2008 3:06 am
Re: rear seatbelt install
I would not be putting my life on the line for a single attach point for a seat belt. I know some people will say a 3/16 screw has a breaking strain of such and such but it’s only a sample test that’s done over thousands made. And they are allowed 5 to break in the sampling test. Reason is I have just been through this exercise as we purchased a number of AN bolts and there was a number of them with mal formed heads. The paper work was all correct so off to the authorities I went . The only bolt that’s standard is guaranteed is a NAS that’s been magafluxed and has a dye marking green on it. The supplier replaced the bolts and was informed by the authorities that this situation was ok. I was informed it’s up to the certified person fitting the parts to make sure all parts have the correct documentation and parts are of a standard as per the manufactures manuals.
Re: rear seatbelt install
Here in the U.S. the PIC is responsible for determining whether the aircraft is in condition for safe flight. (FAR 91.7b). I’m sure we’ve all confirmed that none of the AN3-5A bolts on our planes have “MAC X” markings on the head as outlined by SEB96-7.ghostflyer wrote:... I was informed it’s up to the certified person fitting the parts to make sure all parts have the correct documentation and parts are of a standard as per the manufactures manuals.
Gary
Re: rear seatbelt install
Gary fair enough statement, but I think most would take a step back and look at the big picture. I think it takes a “ system “ to determine whether a plane is safe for flight.
Jim McIntosh..
1953 C170B S/N 25656
02 K1200RS
1953 C170B S/N 25656
02 K1200RS
-
- Posts: 3485
- Joined: Sat May 06, 2006 6:05 pm
Re: rear seatbelt install
The Airframe Innovation website seems to provide the answer to the seat belt attach question:
"FAA Design Approval for seat belt attach hardware for older Cessna models has been included in the STC."
"FAA Design Approval for seat belt attach hardware for older Cessna models has been included in the STC."
Richard Pulley
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
Re: rear seatbelt install
My '52 170B has three 1/4" nutplates on the floor at station 90; one on centerline and two approximately 11" from centerline. It also has two 1/4" nutplates approximately 8" from centerline on the floor at station 108. These are shown in the IPC fig. 23-60.dogone wrote:I am putting an Innovation Airframe single rear seat in my c170. Directly behind the seat and about 14 inches back is a nut plate. I believe it is for a 3/16 bolt. Is this strong enough for attaching the belt (both sides)? I have not been able to get clear information on this.
Last edited by n2582d on Tue Jan 15, 2019 11:45 pm, edited 1 time in total.
Gary
-
- Posts: 3485
- Joined: Sat May 06, 2006 6:05 pm
Re: rear seatbelt install
Wow! That would be nice having all those tiedown options, my 1951 170A has nothing other than the original rear seat attach bolt nutplates.
Last edited by hilltop170 on Tue Jan 15, 2019 11:43 pm, edited 2 times in total.
Richard Pulley
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
Re: rear seatbelt install
Mine has these as well in what sounds like the same locations.n2582d wrote:My '52 170B has three 1/4" nutplates on the floor at station 90; one on centerline and two approximately 11" from centerline. It also has two 1/4" nutplates approximately 8" from centerline on the floor at station 108. These are shown in the IPC fig. 28-60.
Karl
'53 170B N3158B SN:25400
ASW-20BL
'53 170B N3158B SN:25400
ASW-20BL
Re: rear seatbelt install
lownslow and n2582d ; you have what I have been trying to describe. I am not near my AME and was just trying get clear in my own mind if the other hard point was good for the belt. I am not yet familiar with the Cessna original placement. I hope to clarify when I talk to my AME.